I spoke with my contact regarding the LED Wedge Base Replacement Lamp # DI68VR and he said that he is unaware of any safety issues.
The issue that he typically has seen is when a poor quality converter is installed they will have power fluctuations that can damage the LED light. view full answer...
We do carry skirts that fit the 2009 Keystone Challenger Fifth Wheel however I would need to know the model of fifth wheel to give you an exact answer. The skirts that fit the Challenger are either 236" long x 64" tall, 266" long x 64" tall or 292" long x 68" tall.
If you are not sure of the model of Challenger, you can always measure the front open area of the fifth wheel trailer. Measure along each side for length and measure from the bottom of the overhang to the ground for height.... view full answer...
Landing gear lead leg # LC119102 has bracket stops places on the opposite side of the shaft. Lead leg # LG-179013 is a universal option and has bracket stops on both sides. So if you want you can use the universal leg. view full answer...
I spoke to my contact at Lippert and he told me the correct hydraulic cylinder replacement for your 2009 Keystone Challenger Fifth Wheel is the Lippert Replacement Hydraulic Cylinder for RV Slide-Out - 53" Long
# LC342328. view full answer...
Your tire size of 235/80-16 is a fit for the width of the trailer wheel part # AM22658HWT which is a 16 inch diameter wheel with a width of 6-1/2 inches.
Your tire size actually fits rim widths that are between 6 and 7-1/2 inches. view full answer...
The Replacement Lead Leg # LG-179013 and Follow Leg # LG-179014 referenced in your question are direct replacement legs for the Stromberg Carlson # LG-1, # LG-3, and # LG-183708 Landing Gear Systems. They can also be used with many systems from Atwood, Venture, and Lippert.
I am not sure of the exact system you have installed on your Keystone Challenger, so your best bet is to take a few measurements to see if these replacement legs will fit with your existing brackets. They have a leg... view full answer...
The Electric Trailer Brake Kit part # AKEBRK-7-SA does not come with the hub/drum. In order to find the correct hub/drums we are going to need to know your bearing numbers or measurements. We would also need to know the bolt pattern of your wheels. I have attached articles for determining both bearing numbers/measurements and bolt pattern for you. If you can provide me with the bearing numbers/measurements then I would be happy to help you make sure you get the correct hub/drums but if... view full answer...
Based on the information we have in our fitguide the 2009 Keystone Challenger 30TRL Fifth Wheel has a Coleman unit from the factory which would have a 9-pin connector. The Furrion Chill Replacement RV Air Conditioner for Furrion Setup - 15,000 Btu - White # FR58PR you were looking at has a 6-pin connector so that's why it isn't recommended.
Instead you simply need the Furrion Chill Replacement RV Air Conditioner for Coleman Setup # FR42PV which will come with an adapter to plug into a... view full answer...
The Aluminum Sendel Series T02 Machined Trailer Wheel # AM22654 that you referenced doesn't come with a center cap but one cap be added. This wheel has a 4.25" diameter pilot hole which we have a center caps compatible with.
We have the Excalibur Center Cap # 425EZ which comes in chrome and the Americana Trailer Wheel Center Cap # AM90077 which comes in stainless steel. Both caps have removable centers (like what you see in your pictures) so it is just a matter of choosing which style... view full answer...
Manufacturers do not list the door handle locks used so you would need to remove the door handle lock from the entry door of your 2009 Keystone Challenger 5th Wheel and measure the cutout hole to find the size needed. For example the Bauer Products Keyless Entry Camper Door Lock - Right Hand - 6-1/8" Wide x 4-5/8" Tall # BA76FR will require a cutout hole of 3-3/4" tall x 2-3/4" wide.
The elbow under your bathroom sink is called a trap. If you're trying to replace the trap under your sink... view full answer...
In order to determine which replacement lead leg you need on your 2005 Keystone Challenger, you'll need to know the model of the landing gear on your trailer (we have no way of knowing what you have), and measure it's outer tube length.
For example, if you have a Venture, Lippert, or Stromberg Carlson landing gear with legs that measure 33-1/2 inches you can replace the leg with the Replacement Lead Leg for Stromberg Carlson Landing Gear # LG-177202 and the part # LC122533 is 29-1/2 inches.... view full answer...
We do not have any type of database with a list that has the parts for each year, make and model of trailer so you will need to do some measuring to figure out what will fit on your 2009 Keystone Challenger.
Measure your landing gear brackets from outside to outside like in the accompanying photo and if they have standard weld stop measurements of 17-1/2 inches outside to outside and 15-1/2 inches inside to inside I recommend checking out the Electric Landing Gear Set # LG-3. view full answer...
In order to choose the correct Trailair Pin Box for your Keystone Laredo you will need to know the manufacturer and model number of your current pin box, which should be on a sticker or stamp somewhere on the pin box itself. If you cannot find it, simply call the trailer manufacturer with your VIN and they should be able to tell you what pin box it is. You will be able to select the correct replacement from there.
For example, the Trailair # LC155943 is designed to replace Lippert 1116... view full answer...
You have a very common landing gear setup on your trailer. For a replacement gearbox the aluminum version part # LC276602 would be your best option as it will hold up better than the plastic one. For a new motor you'd want the part # LC142178.
For a kit that includes everything you'd want the part # LG-3 and you'd be set. view full answer...